Battery pull tab

Introduction: Pull Tab Switch Paper knob switches worked all right with copper tape circuits. But by no means would they earn a Six Sigma award. The performance of brass fastener switches (which you'll see in an upcoming Instructable) was also spotty. I then wound up at the highlowtech.org site and saw their pull tab switches. These look simpler and perform better than other switches. A student can make one of these in minutes and spend the rest of the time investigating circuitry. Step 1: Tools and Materials Craft knife (Unfortunately. The rest of the project only requires five-year-old motor skills. If you don't want students to learn knife skills, yet, do some pre-cutting.)A pair of scissors can also helpCard stock or index cardCopper Tape (Available as Slug and Snail tape at hardware and garden stores and home centers)LED3V battery Step 2: Cut Some Tape I cut eight quarter inch lengths from the end. You might need more or less. Step 3: Layout Circuit Leave gaps for the three components: battery, led, and switch. Step 4: Cut Two Slots Cut two 1/4-inch long slots above and below the bottom two lengths of the tape. Step 5: Add Copper Tape Add copper tape to your paper slip so that it will make contact in the upper side of the paper. Step 6: Tape Battery and LED Use a little bit more copper tape to secure the leads on your other components. Step 7: Mark Your Tab Write on and off symbols where

Feedbacks#update" id="js_page_content" data-controller="feedbacks" data-feedbacks-load-form-value="/admin/feedbacks/comments/new?question_id=2822378">The following steps explain how to install your Blink Floodlight Mount. A Blink Outdoor (3rd Gen) camera must be set up in your Blink account before attaching the camera to the mount.Your Blink Floodlight Mount uses 4 alkaline D-cell batteries to operate and comes preinstalled in the mount. Remove the pull-tab in the battery compartment to activate power to the Floodlight Mount. To access or replace the batteries, dismount the device and twist the back cover open to access the battery compartment.Note: Older Blink Outdoor camera models (XT and XT2) aren’t compatible with the Blink Floodlight Mount.Installing the Outdoor (3rd Gen) camera to the Floodlight Mount1. Twist to remove the back cover of the Floodlight Mount and press the side buttons on the battery lid to open the battery compartment. Remove the battery pull-tabs. If your pull-tab is missing or broken, ensure both positive and negative ends of each battery are clear of any coverings and reattempt installation.Once the batteries are installed, close the compartment and reattach the back cover.DeleteWarningThe LED lights will flash brightly once the back cover is attached. To avoid direct light exposure, don’t look directly at the lights when this occurs.2. Remove the back cover from your Blink Outdoor (3rd Gen) camera. Learn more about how to remove and attach the back cover on your Blink Outdoor camera.3. Detach the USB cover from the Outdoor (3rd Gen) camera back cover. This will ensure you have an optimal weather-resistant seal between the Floodlight Mount’s micro-USB cable and your camera. Once the USB cover is fully removed, reattach the back cover back on your Outdoor camera.USB Cover4. Firmly plug the Floodlight Mount’s micro-USB cable into your Outdoor (3rd Gen) camera. Ensure you have a tight seal on all sides.The Floodlight Mount self-configures when you plug the USB cable into your Outdoor (3rd Gen) camera. On the Blink app, a notification appears that your Floodlight Mount is connected, as well as added to your camera.Tap OK to continue. 5. Line up hole on the back of the camera to the swivel neck and snap it onto

You cannot safely view and access the component, remove the server from the rack. Remove the top cover from the server as described in Removing the Server Top Cover. Locate the USB socket on the motherboard, directly in front of PCIe riser 2. Grasp the USB drive and pull it horizontally to free it from the socket. Step 2 Install a new internal USB drive: Align the USB drive with the socket. Push the USB drive horizontally to fully engage it with the socket. Replace the top cover to the server. Replace the server in the rack, replace cables, and then fully power on the server by pressing the Power button. Figure 26. Location of Internal USB Port 1 Location of horizontal USB socket on motherboard - Enabling or Disabling the Internal USB Port The factory default is that all USB ports on the server are enabled. However, the internal USB port can be enabled or disabled in the server BIOS. Procedure Step 1 Enter the BIOS Setup Utility by pressing the F2 key when prompted during bootup. Step 2 Navigate to the Advanced tab. Step 3 On the Advanced tab, select USB Configuration. Step 4 On the USB Configuration page, select USB Ports Configuration. Step 5 Scroll to USB Port: Internal, press Enter, and then choose either Enabled or Disabled from the dialog box. Step 6 Press F10 to save and exit the utility. Replacing the RTC Battery Warning There is danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. [Statement 1015] Warning Recyclers: Do not shred the battery! Make sure you dispose of the battery according to appropriate regulations for your country or locale. Caution

Of the lock. TO LOCK THE BATTERY COMPARTMENT Do not lock the battery compartment until you have activated the battery and tested the battery back-up. Activate the battery back-up by removing the unlocking the battery compartment. "Pull to Activate Battery Back-Up" tab. Or, install battery back-up. Battery back-up cannot work until you install the battery in the correct position (Match "+" to "+" and "-" to "-") Push and hold test button until the alarm sounds: 3 beeps, pause, 3 beeps, pause. If the unit does not alarm during testing, DO NOT lock the battery compartment! Install a new battery and test again. If the Smoke Alarm still does not alarm, replace it immediately. Using needle-nose pliers or a utility knife, detach one locking pin from the mounting bracket. Push the locking pin through the black dot on the label on the back of the Smoke Alarm. TO UNLOCK THE BATTERY COMPARTMENT Once the Smoke Alarm is installed, you must disconnect it from the AC power before unlocking the battery compartment. ELECTRICAL SHOCK HAZARD. Turn off the power to the area where the Smoke Alarm is installed before removing it from the mounting bracket. Failure to turn off the power first may result in serious electrical shock, injury or death. Always discharge the branch circuit before servicing an AC or AC/DC Smoke Alarm. First, turn off the AC power at the circuit breaker or fuse box. Next, remove the battery from Smoke Alarms with battery back-up. Finally, press and hold the test button for 5-10 seconds to discharge the branch circuit. Remove the Smoke Alarm from the mounting bracket. If the unit is locked to the bracket, see the section "To Unlock the Mounting Bracket." Disconnect the power connector by gently prying it away from the back of the Smoke